Warps

$259.00

Digital cross-modulator, with continuous morphing between modulation algorithms.

Features

  • Continuous morphing between 7 cross-modulation algorithms: crossfade, cross-folding, digital model of analog diode ring-modulation, digital ring-modulation, bitwise XOR modulation, octaver/comparator, 20-band vocoder.
  • Control of timbre richness/brightness.
  • Each audio input has a built-in digital VCA with emulation of analog soft-clipping.
  • Audio input 1 can be replaced by an internal digital oscillator with through-zero FM. Available waveforms: sine, triangle, sawtooth, pulse, filtered noise.

Controls

  • Modulation algorithm morphing.
  • Timbre richness.
  • Input gain/distortion for audio inputs 1 and 2.
  • Internal oscillator waveform.

Inputs and outputs

  • Audio input 1 (carrier) level CV (or internal oscillator 1V/Oct CV), -1V to +8V.
  • Audio input 2 (modulator) level CV, -1V to +8V.
  • Modulation algorithm morphing CV, -5V to +5V.
  • Timbre CV, -5V to +5V.
  • Audio input 1 (or internal oscillator through-zero FM). Modular level expected (up to 15 Vpp).
  • Audio input 2. Modular level expected (up to 15 Vpp).
  • Cross-modulated signal output.
  • Auxiliary output: internal oscillator signal (when enabled) or mix of inputs 1 and 2 (post digital VCA).

Technical characteristics

  • Input impedances: 100k.
  • AD/DA: 16-bit, 96kHz.
  • Internal processing: 32-bit floating point, 576kHz (32kHz for vocoder).
  • Open-source hardware and firmware.
  • Easy firmware updates through an audio interface.
  • Cortex-M4 ARM processor.
  • 10-HP.
  • Current consumption: +12V: 110mA ; -12V: 5mA.

Overview

Evolved from the oscillator mixing section of Mutable Instruments’ desktop hybrid synths, Warps is designed to blend and combine two audio signals. A variety of cross-modulation methods – some of them emulating classic analog circuits, some of them purely digital – are provided by the module. With Warps, the cross-modulated sound can be sculpted with control voltages along 4 dimensions: by controlling the amplitude and distorting the input signals, by smoothly scanning through the collection of modulation algorithms, and by adjusting a timbre parameter controlling the brightness/harshness of the modulated signal.

Most cross-modulation algorithms provided in Warps make the distinction between a carrier signal and a modulator signal: the carrier signal will be filtered or modulated to acquire some of the characteristics of the modulator signal. However, some other algorithms emulate symmetrical circuits and do not make such a distinction (the underlying mathematical operation is commutative).

Since many classic cross-modulation effects work best when the carrier is a simple waveform – for example, a sine wave for ring-modulation or a buzzing waveform simulating glottal pulses for vocoding – Warps includes a digital oscillator offering a handful of classic waveforms. This internal oscillator tracks V/Oct and will replace the carrier audio input – freeing up one oscillator in your system for other duties!

Download the quick start guide.

Installation

Mutable Instruments’ Warps is designed for Eurorack synthesizer systems and occupies 10 HP of space. It requires a -12V / +12V supply (2×5 connector), consuming 5mA from the -12V rail and 110mA from the +12V rail. The red stripe of the ribbon cable must be oriented on the same side as the “Red stripe” marking on the printed circuit board.

Controls, inputs and outputs

A. Modulation algorithm. This knob selects which signal processing operation is performed on the carrier and modulator. The algorithms are described in further details in the next section.

B. Modulation timbre. This knob controls the intensity of the high harmonics created by cross-modulation – or provides another dimension of tone control for some algorithms.

C. Internal oscillator state. This button enables the internal oscillator and selects its waveform. The color of the LED depends on the oscillator waveform – when the LED is off, the internal oscillator is disabled and an external signal is used as a carrier.

D. External carrier amplitude or internal oscillator frequency. When an external carrier is used (that is to say, when the internal oscillator is switched off), this knob controls the amplitude of the carrier, or the amount of amplitude modulation from the channel 1 LEVEL CV input. When the internal oscillator is active, this knob controls its frequency.

E. Modulator amplitude. This knob controls the amplitude of the modulator, or the amount of amplitude modulation from the channel 2 LEVEL CV input. Note that gains above 1.0 can be applied, for a warm overdrive effect!

1. External carrier amplitude or internal oscillator frequency CV input. When the internal oscillator is switched off, this CV input controls the gain of the carrier input. When the internal oscillator is enabled, it acts instead as a V/Oct control for the oscillator frequency.

2. Modulator amplitude CV input. This CV input controls the gain of the modulator input. Just like its carrier counterpart, it is internally normalized to a constant +5V source when no patch cable is plugged in. When a signal is patched into this input, the amount of CV modulation is controlled by the Modulator amplitude knob (E).

3. Algorithm CV input. The CV on this input is added to the position of the Modulation algorithm knob (A).

4. Timbre CV input. The CV on this input is added to the position of the Modulation timbre knob (B).

5. 6. Carrier (1) and modulator (2) audio inputs. Warps expects modular-level signals (typically 10Vpp, up to 20Vpp).

7. Modulator output (1×2). This is the main audio output.

8. Auxiliary output. This output carries, when the internal oscillator is disabled, the sum of the carrier and the modulator, post VCA. Otherwise, it carries the raw waveform from the internal oscillator.

Modulation algorithms

Crossfade. The carrier and modulator are crossfaded into each other, using a constant-power law.TIMBRE controls the crossfading position – both signals are equally mixed at 12 o’clock.

Crossfolding. The carrier and modulator are summed, a tiny bit of cross-modulation product is added to spice things up, and the resulting signal is sent to a wavefolder the amount of which is controlled by TIMBRE.

Diode ring-modulation. The carrier and modulator are crudely multiplied, using a digital model of a diode ring-modulator. TIMBRE post-processes the resulting signal with a variable amount of gain (and emulated diode clipping).

Digital ring-modulation. A gentler version of the previous algorithm which uses a proper multiplication operation in the digital domain, which will sound more similar to all the AD633-based analog ring-modulators out there! TIMBRE post-processes the signal with a gain boost and soft-clipping.

XOR modulation. Both carrier and modulator are converted to 16-bit integers, and the two resulting numbers are XOR’ed bit by bit. TIMBRE controls which bits are XOR’ed together.

Comparison and rectification. A handful of signals are synthesized through comparison operations (“replace the negative portion of the carrier’s signal by the modulator”, “if the absolute value of the carrier is greater than the absolute value of the modulator, output the modulator else the carrier”…).TIMBRE morphs through these signals (some of which having an octave pedal flavor).

  

Vocoder. A classic implementation of an analog vocoder, with a bank of 20 analysis and 20 synthesis third-octave 48dB filters. The modulator sub-band signals are processed by envelope followers from which are derived the gains of each of the carrier sub-band signals. TIMBRE warps the connections between the modulator’s envelope followers and the carrier’s gain elements – effectively shifting up or down the formants extracted from the modulator signal.

As the ALGORITHM knob is turned clockwise, the release time of the envelope followers is increased.

By turning the knob fully clockwise, the modulator signal is frozen. The carrier is filtered by whichever formants were present in the modulator signal before the knob reached this position.

Internal oscillator

Press the INT. OSC button (C) to enable the internal oscillator or select its waveform. Because cross-modulation algorithms work best with harmonically simple signals, while vocoders work better with harmonically rich signals, the available waveforms are different: sine, triangle and sawtooth for the former, and sawtooth, pulse and low-pass filtered noise for the later.

Some of the inputs, outputs or controls operate differently when the internal oscillator is enabled:

  • The LEVEL knob (D) and CV input (1) control the internal oscillator frequency.
  • The Carrier audio input (5) phase-modulates the internal oscillator, or feeds an external source of noise into the low-pass filter.
  • The AUX output (8) contains the signal generated by the internal oscillator.

Advanced topics

Calibration procedure

Say no to trimmers! Warps uses digital processing to scale its input control voltages.

To calibrate the unit:

  1. Disconnect all CV inputs.
  2. Hold the INT. OSC button for five seconds until the ALGORITHM knob blinks in turquoise and the oscillator state LED blinks in yellow.
  3. Connect a patch cable to the LEVEL 2 CV input. Leave the other end of the cable unplugged.
  4. Connect the CV output of a well-calibrated keyboard interface or MIDI-CV converter to theLEVEL 1 CV input.
  5. Input a CV corresponding to a C2 note (1V).
  6. Press the INT. OSC button. The ALGORITHM knob blinks in fuchsia.
  7. Input a CV corresponding to a C4 note (3V).
  8. Press the INT. OSC button.
  9. Calibration is done!

Firmware update procedure

Unplug all CV inputs/outputs from the module. Connect the output of your audio interface/sound card to the Carrier audio input (5) input. Power on your modular system with the INT. OSC (C) push-button pressed. The INT. OSC LED will blink in orange.

Make sure that no additional sound (such as email notification sounds, background music etc.) from your computer will be played during the procedure. Make sure that your speakers/monitors are not connected to your audio interface – the noises emitted during the procedure are aggressive and can harm your hearing. On non-studio audio equipment (for example the line output from a desktop computer), you might have to turn up the volume to the maximum.

When you are all set, play the firmware update file into the module. While the module receives data, the color of the ALGORITHM knob will reflect signal level – green or yellow is fine, red is too high! You can use the Carrier amplitude (D) knob to adjust the input gain.

In case the signal level is too weak, the LEDs will blink in red. Press the INT. OSC button and retry with a correct gain. If this does not help, please retry the procedure from another computer/audio interface, and make sure that no piece of equipment (equalizer, FX processor) is inserted in the signal chain.

Hackers and modders will be happy to know that Warps can also be reprogrammed with a USB->serial adapter and stm32loader.py, and that the board has a mini-JTAG connector.

Warranty

This product is covered by Mutable Instruments’ warranty, for one year following the date of manufacture. This warranty covers any defect in the manufacturing of this product. This warranty does not cover any damage or malfunction caused by incorrect use – such as, but not limited to, power cables connected backwards, excessive voltage levels, or exposure to extreme temperature or moisture levels.

The warranty covers replacement or repair, as decided by Mutable Instruments. Please contact our customer service (support@mutable-instruments.net) for a return authorization before sending the module. The cost of sending a module back for servicing is paid for by the customer.

Mutable Instruments encourages modding and hacking, but we will not service modified units or provide any assistance in the realization of mods. We provide an “unbricking” (firmware reinstallation and reinitialization) service in the event of a failed firmware upgrade procedure. We do not “unbrick” devices if a custom firmware has been installed on them.